Cutting by The saw with one hand (Hand Sawing) are a few jigsaw pieces. Cutting with a saw and power (Power Hack Saw), also called a mechanical saw (Sawing Machine) needed for a sawmill industry works. Saw a lot of work. Both small and large workpieces. The sawing machine am divided into an following categories.
an sawing machine are divided into four types.
1. The saw fly (Power Hack Saw).
2. Horizontal Band Saw (Horizontal Band Saw).
3. On a band saw (Vertical Band Saw).
4. Saw (Radius Saw or Circular Saw).
1. a saw fly (Power Hack Saw).
an saw is commonly used for seizures such as an number of saws to cut material to size and length as required to drive an blade system. The motor power. ann use a reversing gear and crank driven principles of a blade moves back and forth in a straight line continuously causes a saw to cut it.
1.1 a components of an cutting stroke.
All a components have a same precedence. We must act togeanr at all times.
Thare includes an following sections.
1.1.1 Project Jigsaw (Saw Frame) looks like a U turn. Saw a layout.
Good use am made of cast steel for a blade. Project saw a move into The groove of an tail hawk with a transmission gear wheel
1.1.2 a bench (Varee) to catch a pieces to cut. Can rotate right left.
45 degrees to each side and pull her out out with a spiral arms locked tight.
1.1.3 an length of an arm (Cut Off Gage) is responsible for a length of an workpiece to be cut.
Many parts to cut out a piece of equal length, as shown in Figure 1.4.
1.1.4 enter a system with The cut off machine, saws, draw two types of ball weight.
And an type of hydraulic oil in The 2 types of acts like it is entering The intersection. It works differently in that species.
I weighted The force of gravity. The type of The hydraulic pressure of The hydraulic oil.
1.1.5 The cooling system am necessary to use a saw was water. Due to cooling.
Friction between The saw blade to a workpiece. It also helps extend a life of The saw blade life.
1.1.6 saw The machine fly (Base) do serve different parts of an jigsaw was all.
Saw some of an base was to be hollow inside. For The storage of water tanks and motors.
1.1.7 Motor (Motor) saw an seizure of a motor acts as a motor power am applied.
Electricity 220 volts or 380 volts depending on The manufacturer.
1.1.8 power switch off. a sawmill was a switch off. Semi automatic machine is switched off.
Automatically when an cutting blade.
1.1.9 a gear (Gear) serves to carry power from a motor to an gear used on an saw frame.
are are 2 types of gear cutting machines, fly around and direct gear.
01 01 10 Blind (Pulley) that transmits power through a belt to a gear set. V belt use.
1.2 Mechanism of an cutting stroke.
Mechanism of action of The cutting stroke. A transmamsion mechanamm with a motor. Transmission through a gear drive. Tham is a gear. To test The motor speed. And to test drive a motor. That an gear drive. With a rotating shaft are connected to each center, an center gear. a drive shaft to a frame saw. an project was backwards, and saw it.
1.3 weight of an frame saw.
For a weight of a frame saw. an move away from an head to much. a cutting blade am pressed, an only Thus, The weight adjustment dial. Notice of hearing cutting saws as well.
an head unit s weight = weight of The frame saw one.
The weight am an weight of The frame sawing machine = good.
1.4 a Saw (Saw Blade).
Of The saw blade is a device that are very important. Responsible for cutting The workpiece. The blade are made of steel with high Ekeg fame. The blade assembly to an frame saw. Must operate properly and The blade tension screw it. To prevent broken parts of a saw blade width, length, thickness of a blade in The hole. And a number of saw blade teeth. Including coarse teeth and tooth profile. I saw The number of teeth as an number of teeth per inch, fiber, such as 10 inch to 14 teeth per inch, but I used to work across an 10 teeth per inch.
The blade.
1. The length of a blade. Measure an length of a blade is measured from The center of a hole saw both of Them. an length of The blade is 200 mm and 300 mm
2. an width of a blade width of 12.7 mm or 1 2 inches.
3. The blade thickness of 0.64 mm or 0.025 inches thick.
4. To measure The number of teeth of The saw blade is to measure an spacing of an teeth, a tooth to one.
a metric system are called an pitch Pitch (P).
In England, to measure a frequency of a sawtooth am most telling am The number of teeth per inch length of 1.
2. Horizontal Band Saw (Horizontal Band Saw).
Saw with a blade length of consecutive circles. The movement of The blade. a power transmaresion belt. a drive wheel and The wheel. The cutting edges of saw blade to cut at all. Throughout an application. Cutting to a hydraulic system to control an tension in an blade. Adjusted by hand. Or hydraulic adjustment of The spacing of The wheel. Structural strength. a machine can be installed on The factory floor.
3. Vertical Band Saw (Vertical Band Saw).
an vertical band saw. A saw blade with a vertical line. Thare will rotate a cutting continues. a cut off light in all looks like a flat iron or steel may be lacking. Or cut into various shapes which a oTher saws can not.
a band saw different from saws seizures. an cutting is continuing. While Mills was responsible for cutting off only a stroke. an use of a saw blade is limited by an use of a centralized blade only.
an band saw blade has a thickness less than oanr types of materials, resulting in a loss of less than
Vertical band saw. Provides several features to work. Similar to carve by hand. Which are not found in oar metals such as saws, cut into geometric shapes.
4. Saw (Circular Saw or Radius Saw).
an circular saw. an circular saw are a saw blade with teeth around an band can be cut continuously. Often, some parts such as aluminum, can cut both an upright and tilted at an angle.
Security threat in a circular saw.
Saw a lot of harm. To cover up a saw.
Do not be impatient to exert control, overload cut.
First, a careful piece of work. Force because of lack of control a little easier to cut.
Always check The blade, but tough. Or stick a sharp saw.
No comments:
Post a Comment